Abstract:The spatial Sigma-Delta ($\Sigma\Delta$) architecture can be leveraged to reduce the quantization noise and enhance the effective resolution of few-bit analog-to-digital converters (ADCs) at certain spatial frequencies of interest. Utilizing the variational Bayesian (VB) inference framework, this paper develops novel data detection algorithms tailored for massive multiple-input multiple-output (MIMO) systems with few-bit $\Sigma\Delta$ ADCs and angular channel models, where uplink signals are confined to a specific angular sector. We start by modeling the corresponding Bayesian networks for the $1^{\mathrm{st}}$- and $2^{\mathrm{nd}}$-order $\Sigma\Delta$ receivers. Next, we propose an iterative algorithm, referred to as Sigma-Delta variational Bayes (SD-VB), for MIMO detection, offering low-complexity updates through closed-form expressions of the variational densities of the latent variables. Simulation results show that the proposed $2^{\mathrm{nd}}$-order SD-VB algorithm delivers the best symbol error rate (SER) performance while maintaining the same computational complexity as in unquantized systems, matched-filtering VB with conventional quantization, and linear minimum mean-squared error (LMMSE) methods. Moreover, the $1^{\mathrm{st}}$- and $2^{\mathrm{nd}}$-order SD-VB algorithms achieve their lowest SER at an antenna separation of one-fourth wavelength for a fixed number of antenna elements. The effects of the steering angle of the $\Sigma\Delta$ architecture, the number of ADC resolution bits, and the number of antennas and users are also extensively analyzed.
Abstract:We propose a new reconfigurable intelligent surface (RIS) structure, referred to as interconnected RIS (I-RIS), which allows the RIS elements to be interconnected and share the incident signals using simple binary radio frequency (RF) switches and mix them into the reflecting signals. This structure enables multi-user scaling and requires fewer elements (i.e., a compact structure) compared to standard RIS (S-RIS), which assumes no interconnection between the elements. The I-RIS compact design makes it practical for deployment on space-limited nodes, e.g., unmanned aerial vehicles (UAVs). Hence, in this work, we propose a beamforming design based on I-RIS in a multi-user network, where we use binary RF switches as RIS elements. We show that our switch-based I-RIS offers a higher gain compared to an S-RIS using phase shifters. Finally, we introduce two optimization methods, sigmoid filled function (SFF) and semi-definite binary optimization (SBO), to optimize the RIS elements and evaluate their performance in terms of sum-rate and complexity.
Abstract:In this paper, we study the advantages of using reconfigurable intelligent surfaces (RISs) for interference suppression in single-input single-output (SISO) distributed Internet of Things (IoT) networks. Implementing RIS-assisted networks confronts various problems, mostly related to the control and placement of the RIS. To tackle the control-related challenges, we consider noisy and local channel knowledge, based on which we devise algorithms to optimize the potentially distributed RISs to achieve an overall network objective, such as the sum-rate. We use a network with a centralized RIS as a benchmark for our comparisons. We further assume low-bit phase shifters at the RIS to capture real-world hardware limitations. We also study the placement of the RIS and analytically quantify the minimum required degrees-of-control for the RIS as a function of its location to guarantee a specific network performance metric and verify the results via simulations.
Abstract:With the turn of new decade, wireless communications face a major challenge on connecting many more new users and devices, at the same time being energy efficient and minimizing its carbon footprint. However, the current approaches to address the growing number of users and spectrum demands, like traditional fully digital architectures for Massive MIMO, demand exorbitant energy consumption. The reason is that traditionally MIMO requires a separate RF chain per antenna, so the power consumption scales with number of antennas, instead of number of users, hence becomes energy inefficient. Instead, GreenMO creates a new massive MIMO architecture which is able to use many more antennas while keeping power consumption to user-proportionate numbers. To achieve this GreenMO introduces for the first time, the concept of virtualization of the RF chain hardware. Instead of laying the RF chains physically to each antenna, GreenMO creates these RF chains virtually in digital domain. This also enables GreenMO to be the first flexible massive MIMO architecture. Since GreenMO's virtual RF chains are created on the fly digitally, it can tune the number of these virtual chains according to the user load, hence always flexibly consume user-proportionate power. Thus, GreenMO paves the way for green and flexible massive MIMO. We prototype GreenMO on a PCB with eight antennas and evaluate it with a WARPv3 SDR platform in an office environment. The results demonstrate that GreenMO is 3x more power-efficient than traditional Massive MIMO and 4x more spectrum-efficient than traditional OFDMA systems, while multiplexing 4 users, and can save upto 40% power in modern 5G NR base stations.