Reducing Dynamic Range in Bistatic Backscatter Communication via Beamforming Design

Considering the exponential growth of Internet-of-Things devices and the goals toward sustainable networks, the complexity should be focused on the infrastructure side. For a massive number of passive devices, backscatter communication (BC) is a promising technology that reduces cost and increases energy efficiency by enabling transmitting information by backscattering radio frequency signals. Two main limitations that restrict the performance of BC are the round-trip path loss effect and the direct link interference (DLI) from the carrier emitter (CE). To circumvent this, we propose a novel transmit beamforming design for a multiple antenna bistatic BC (BiBC) system that realizes both purposes: mitigation of the DLI and increasing the power towards the backscatter device (BD). Additionally, we provide a detector design and the performance is evaluated in terms of the probability of error, for which we also provide a closed-form expression. Finally, simulation results show the superiority of the proposed beamforming design in decreasing DLI over a benchmark scenario that considers maximum-ratio transmission.

Access Point Selection for Bistatic Backscatter Communication in Cell-Free MIMO

Backscatter communication (BC) has emerged as a key technology to satisfy the increasing need for low-cost and green Internet-of-Things (IoT) connectivity, especially in large-scale deployments. Unlike the monostatic BC (MoBC), the bistatic BC (BiBC) has the possibility to decrease the round-trip path loss by having the carrier emitter (CE) and the reader in different locations. Therefore, this work investigates the BiBC in the context of cell-free multiple-input multiple-output (MIMO) networks by exploring the optimal selection of CE and reader among all access points, leveraging prior knowledge about the area where the backscatter device (BD) is located. First, a maximum a posteriori probability (MAP) detector to decode the BD information bits is derived. Then, the exact probability of error for this detector is obtained. In addition, an algorithm to select the best CE-reader pair for serving the specified area is proposed. Finally, simulation results show that the error performance of the BC is improved by the proposed algorithm compared to the benchmark scenario.

Dynamic Range Improvement in Bistatic Backscatter Communication Using Distributed MIMO

Backscatter communication (BSC) is a promising solution for Internet-of-Things (IoT) connections due to its low-complexity, low-cost, and energy-efficient solution for sensors. There are several network infrastructure setups that can be used for BSC with IoT nodes/passive devices. One of them is a bistatic setup where there is a need for high dynamic range and high-resolution analog-to-digital converters at the reader side. In this paper, we investigate a bistatic BSC setup with multiple antennas. We propose a novel algorithm to suppress direct link interference between the carrier emitter (CE) and the reader using beamforming into the nullspace of the CE-reader direct link to decrease the dynamic range of the system and increase the detection performance of the backscatter device (BSD). Further, we derive a Neyman-Pearson (NP) test and an exact closed-form expression for its performance in the detection of the BSD. Finally, simulation results show that the dynamic range of the system is significantly decreased and the detection performance of the BSD is increased by the proposed algorithm compared to a system not using beamforming in the CE, which could then be used in a host of different practical fields such as agriculture, transportation, factories, hospitals, smart cities, and smart homes.

Direct Link Interference Suppression for Bistatic Backscatter Communication in Distributed MIMO

Backscatter communication (BC) is a promising technique for future Internet-of-Things (IoT) owing to its low complexity, low cost, and potential for energy-efficient operation in sensor networks. There are several network infrastructure setups that can be used for BC with IoT nodes. One of them is the bistatic setup where typically there is a need for high dynamic range and high-resolution analog-to-digital converters at the reader. In this paper, we investigate a bistatic BC setup with multiple antennas. We propose a novel transmission scheme, which includes a protocol for channel estimation at the carrier emitter (CE) as well as a transmit beamformer construction that suppresses the direct link interference between the two ends of a bistatic link (namely CE and reader), and increases the detection performance of the backscatter device (BD) symbol. Further, we derive a generalized log-likelihood ratio test (GLRT) to detect the symbol/presence of the BD. We also provide an iterative algorithm to estimate the unknown parameters in the GLRT. Finally, simulation results show that the required dynamic range of the system is significantly decreased, and the detection performance of the BD symbol is increased, by the proposed algorithm compared to a system not using beamforming at the CE.